TAS-SSAについて詳しく解説（後編：取り付け方）
2024-06-27
１ベースプレート取り外し
２回転台取付
３ベースプレート再取り付け
こんにちは！
前回は独立型トーンアームスタンドTAS-SSAの素材や仕様、コンセプトを詳細に解説しました。
今回は後編として使い方や設置イメージなどを解説していければと思います。
取り付け方は至って簡単です。まずは流れを紹介します。
今回はIT-345CR1を取り付ける方法で写真をまとめております。
１ ベースプレートを止めてあるキャップボルト×３を外します
２ ベースプレートに上側から回転台を挿入。下側からワッシャとナットで締め上げます
３ 再びベースプレートをベース本体にキャップボルトを用いて取り付けます
以上です！海外のお客様からもどうやって取り付けるのか？というお問い合わせをよくいただくのですが
改めて流れを知る事で、一般的なプレーヤーボードに取り付けるよりはるかに簡単な事がわかります！
続けてトーンアームをTAS-SSAに設置してみましょう！
Hello!
Last time, we explained in detail the materials, specifications, and concept of the independent tone arm stand TAS-SSA.
Feature article → Detailed explanation of TAS-SSA (Part 1: Specifications and concept)
In this second part, I would like to explain how to use it and how to install it.
Installation is extremely easy. First, I will introduce the flow.
This time, we have put together photos of how to install IT-345CR1.
1. Remove the 3 cap bolts that secure the base plate.
2. Insert the rotating table into the base plate from above. Tighten from the bottom with a washer and nut.
3. Attach the base plate to the base body again using the cap bolts.
that's all! How can customers from overseas install it? I often get asked this question.
By learning the flow once again, you will find that it is much easier than attaching it to a general player board!
Next, let's install the tone arm on TAS-SSA!
Last time, we explained in detail the materials, specifications, and concept of the independent tone arm stand TAS-SSA.
Feature article → Detailed explanation of TAS-SSA (Part 1: Specifications and concept)
In this second part, I would like to explain how to use it and how to install it.
Installation is extremely easy. First, I will introduce the flow.
This time, we have put together photos of how to install IT-345CR1.
1. Remove the 3 cap bolts that secure the base plate.
2. Insert the rotating table into the base plate from above. Tighten from the bottom with a washer and nut.
3. Attach the base plate to the base body again using the cap bolts.
that's all! How can customers from overseas install it? I often get asked this question.
By learning the flow once again, you will find that it is much easier than attaching it to a general player board!
Next, let's install the tone arm on TAS-SSA!
１ケーブルを下から上に通す
２３トーンアームを設置
2台設置イメージ
トーンアームを取り付ける時に注意してほしい事を記載していきます。
１ ケーブルはしっかりDINコネクターが外から見えるぐらい中から出して
しっかりトーンアームの5ピンに刺さっていることを確認する
２ ケーブルをフォローしながら真っすぐにシャフトを降ろしていく
この際ケーブルを引っ張りすぎてケーブルがシャフトから抜けないように気をつける
３ トーンアームの高さを決めたら回転台止めネジをしっかり締める
弊社トーンアームは止めネジの先端に樹脂がついていますのでアームを大きく傷つけません
４ トーンアームに付属しているテンプレートを用いて好きな位置にセッティングする
この際トーンアームのパイプを持ってターンテーブルの中心まで動くところにセッティングすると
正常に動作してくれます
以上です。細かく記載しましたが、ケーブルのDINコネクターとトーンアームの接続の部分は
結構手を抜いてしっかり刺さっていなかったという事がありますので、TAS-SSAを使わなくとも
トーンアームを取り付ける際はお気をつけください。
最後の写真は弊社のオーディオシステムです。
職業柄トーンアームを交換する事が多いのでTAS-SSAを使うことでかなり時短できております。
トーンアームを良く交換するお客様はケーブルもつけっぱなしにして、昇圧トランス側で抜き差しするようにすれば
そのまま近くに置いておく事ができます。飾っておくにもちょっとやそっとじゃ動かないのでオススメです。
以上、今回特別記事としてTAS-SSAを特集させていただきました。
トーンアーム二台持っているけど交換がめんどうだから一台ずっと押し入れに眠っている。
現在ショートアームを使用しているけどロングアームも併用したくなってきた。など
お客様の痒い所に手が届く製品がこちらTAS-SSAだと私たちは確信しております。
トーンアームも長さや素材、内部配線や接点、バランス機構の違いなど、多種多様です。
そのなかでお客様のお気に入りの組み合わせを見つける手助けが出来れば幸いです。
今後もこのように写真で解説しながらIKEDA Sound Labs.の製品を詳しく紹介していきたいと思います。
試聴機の貸し出しもしておりますので、気になった方は是非お問い合わせよりご連絡くださいませ。
前編後編に渡り長文お読みいただきありがとうございました。
IKEDA Sound Labs.ホームページ担当
I will list the things you should pay attention to when installing the tone arm.
1. Pull the cable out from inside so that the DIN connector is visible from the outside.
Make sure that it is firmly attached to pin 5 of the tone arm.
2. Lower the shaft straight while following the cable.
At this time, be careful not to pull the cable too much and cause the cable to come out of the shaft.
3. After determining the height of the tone arm, firmly tighten the rotary table set screw.
Our tone arm has resin on the tip of the set screw, so it will not damage the arm too much.
4 Use the template included with the tone arm to set it in the desired position
At this time, hold the tone arm pipe and set it where it moves to the center of the turntable.
It works normally.
1. Pull the cable out from inside so that the DIN connector is visible from the outside.
Make sure that it is firmly attached to pin 5 of the tone arm.
2. Lower the shaft straight while following the cable.
At this time, be careful not to pull the cable too much and cause the cable to come out of the shaft.
3. After determining the height of the tone arm, firmly tighten the rotary table set screw.
Our tone arm has resin on the tip of the set screw, so it will not damage the arm too much.
4 Use the template included with the tone arm to set it in the desired position
At this time, hold the tone arm pipe and set it where it moves to the center of the turntable.
It works normally.
that's all. I have described it in detail, but the connection part between the cable's DIN connector and the tone arm is
There were times when I cut corners and didn't stick it in properly, so I didn't have to use TAS-SSA.
Please be careful when installing the tone arm.
The last photo is our audio system.
Because of my job, I often have to replace tone arms, so using TAS-SSA saves me a lot of time.
If you frequently replace the tone arm, leave the cable connected and connect/disconnect it at the step-up transformer side.
You can keep it nearby. It is recommended to display it because it will not move if you move it slightly or gently.
There were times when I cut corners and didn't stick it in properly, so I didn't have to use TAS-SSA.
Please be careful when installing the tone arm.
The last photo is our audio system.
Because of my job, I often have to replace tone arms, so using TAS-SSA saves me a lot of time.
If you frequently replace the tone arm, leave the cable connected and connect/disconnect it at the step-up transformer side.
You can keep it nearby. It is recommended to display it because it will not move if you move it slightly or gently.
This concludes our special article featuring TAS-SSA.
I have two tonearms, but it's a pain to replace them, so one always sits in the closet.
I'm currently using the short arm, but I'm starting to want to use the long arm as well. Such
We are confident that TAS-SSA is the product that will help our customers reach their pain points.
Tone arms also come in a wide variety of lengths, materials, internal wiring, contacts, and balance mechanisms.
We would be happy if we could help you find your favorite combination.
I would like to continue to introduce IKEDA Sound Labs.'s products in detail while explaining them with photos like this.
We also rent out listening devices, so if you are interested, please contact us.
Thank you for reading the long article from the first part to the second part.
IKEDA Sound Labs.Homepage charge
I have two tonearms, but it's a pain to replace them, so one always sits in the closet.
I'm currently using the short arm, but I'm starting to want to use the long arm as well. Such
We are confident that TAS-SSA is the product that will help our customers reach their pain points.
Tone arms also come in a wide variety of lengths, materials, internal wiring, contacts, and balance mechanisms.
We would be happy if we could help you find your favorite combination.
I would like to continue to introduce IKEDA Sound Labs.'s products in detail while explaining them with photos like this.
We also rent out listening devices, so if you are interested, please contact us.
Thank you for reading the long article from the first part to the second part.
IKEDA Sound Labs.Homepage charge
